Quality system

Quality is a documentation practice.

A sweetener specification is a promise; a certificate is the evidence that the promise was kept for one lot. This page describes the three gates between the material and the drum, the panel that is measured, and the records that travel with the batch.

Release discipline

Three gates between material and drum.

Every gate leaves a document. If a gate has no document, it did not happen.

01

Specification

The property has to be written before the lot is made: exact identity, assay range, sweetness and taste notes, moisture, particle size and the contaminant panel. A parameter that is not in the specification is not tested at release.

02

Sampling and testing

The sample is drawn from the lot, not from a sample cabinet. The laboratory tests against the agreed method, and the report names the method beside each result. Third-party testing is used where the buyer's review or the destination market requires it.

03

Release

The lot is released only when every parameter is inside its limit, the COA is signed and the document pack is complete. A result outside the range is either rejected or reworked and re-tested; it is not averaged into a pass.

Analytical panel

What gets measured.

The panel is agreed in the quotation, not chosen after the lot is made. The method is named beside every result; a result without a method cannot be compared with another supplier's.

PanelParameters
Identity and assaySpecific marker assay by HPLC or HPLC-RI, with the chromatographic method named · Identity by retention time, IR spectrum or mass confirmation where the grade requires it · Related substances and breakdown products relevant to the sweetener family · Moisture by Karl Fischer or loss on drying, stated on the basis used
Physical and processAppearance, colour and odour · Particle size distribution and bulk density · Solubility, clarity of solution and pH where relevant · Sweetness equivalence and taste notes at a stated use level
ContaminantsLead, arsenic, cadmium and mercury by ICP-MS · Microbiology: APC, yeast and mould, E. coli, Salmonella · Residual solvents matched to the purification system · Foreign matter and ash where the grade requires it

Method transparency

  • The certificate names the method for every result, including the glycoside, polyol or fibre method.
  • A “not detected” result carries the detection limit of the method.
  • A calculated figure, such as the total glycoside content, names the assays it comes from.
  • Third-party reports are issued on the same sample as the supplier's certificate where possible.

Document pack

Six files, one lot number.

Each file answers a different review. A COA is not a TDS, and neither one replaces an allergen statement.

01

Certificate of analysis

Batch-specific results for identity, assay, sweetness-relevant impurities, moisture, particle size, heavy metals and microbiology, with the method named against each parameter.

02

Technical data sheet

Chemical form, CAS number, specification ranges, sweetness versus sucrose, solubility, bulk density, recommended storage and the grades available for the same sweetener.

03

Safety data sheet

A 16-section SDS issued against the exact grade supplied, in the format your EHS team already files.

04

Allergen, GMO and origin statements

Declarations covering the major allergen list, gluten, animal-derived inputs, GMO status and the manufacturing site, signed for the batch.

05

Residual solvent and contaminant statements

The solvent system used in purification, plus heavy-metal and microbiological results against the destination-market limits.

06

Specification comparison

A line-by-line comparison of our specification against the one you sent, including where we cannot match and why.

Certificates

Certified, and on file.

NSF 455-2 GMP ISO 22000 HACCP ISO 9001 HALAL USDA Organic EU Organic

Certified to NSF 455-2 GMP, ISO 22000, HACCP, ISO 9001, HALAL, USDA Organic and EU Organic. Current copies are available with the quotation or on request.

What the file contains

  • Identity, assay, method, release limit and the result for the lot.
  • Moisture, particle size, bulk density and the contaminant panel.
  • Taste and solubility data on the technical data sheet.
  • The lot number, manufacturing date and retained-sample record.

The file describes the material and the batch. It is a technical record, not a marketing page.

Questions

Before you ask for the file

Which documents ship with a lot?

A batch-specific COA, TDS, SDS, allergen and GMO statements, an origin record and a residual-solvent statement. Third-party heavy-metal or microbiological reports can be added where the buyer's review requires them.

Which certificates do you hold?

NSF 455-2 GMP, ISO 22000, HACCP, ISO 9001, HALAL, USDA Organic and EU Organic. Current copies are available with the quotation, and a product-specific statement is issued against the grade and the batch.

What is the difference between a specimen COA and a batch COA?

A specimen shows the format: parameter, method, limit and the place where a result would be printed. A batch COA carries the lot number and the result for that lot, and is signed against the specification agreed in the quotation.

How long are samples and records kept?

A retained sample is kept from each released lot so a later question can be checked against the same material. The retention period is agreed in the supplier qualification file and stated in the TDS.

When is third-party testing worth ordering?

On a first shipment from a new source, when the identity of the material is critical to the customer's specification, or when an outside report is requested. The useful panel answers the open question; it is not a full repeat of the supplier's certificate.

Next step

Ask for the documents before the price.

Tell us the ingredient, the grade and the destination market. We will send the specification, a sample COA and the document list we can support for that lot.